Wednesday, 29 February 2012

Reduction linocut, stage 6 and 7

Stage 6: Blue shadow for the wall that goes all the way across the picture.

Reduction linocut, stage 6

As soon as I had printed all of these, I realised I'd forgotten to put on all the blue that I needed. So stage 7 has just a bit more ink:

Reduction linocut, stage 7

(Spot the difference.)

Monday, 27 February 2012

Reduction linocut, stages 4 and 5

Stage 4 has just a slightly darker green at the bottom of the image; I wanted to get that bit of grass right before moving on the more complicated parts of the print.

Reduction linocut, stage 4

Stage 5 has a darker green over the rest of the picture.

Reduction linocut, stage 5

These photos are deceiving: the two plain green patches in the bottom left and right are the same colour in both stages, but the second looks lighter and much yellower now it's against the darker green on the rest of the print.

Friday, 24 February 2012

Reduction linocut, stage 3

Third layer: Gradient from blue green at the top, down to yellow green at the bottom. The earlier layers start to make more sense.

Reduction linocut, stage 3

Thursday, 23 February 2012

Reduction linocut, stage 2

Another layer of loose inking across the print.

Linocut, stage 2

Fingers crossed that these colours aren't already too dark.

Monday, 13 February 2012

The longest print

Longest in time, that is. This print has been "work in progress" for months.

First version: I transferred the image onto the linoblock, and drew over it. I looked at the block for a long time, and decided that something was wrong: the composition. The picture has a strong diagonal element across the entire width. But reading from left to right it goes downward: a negative movement.

It would look better going upward.

"But that's not what it was like in real life."

Dilemma: Record the world as it is, or "improve" it for the sake of making a better picture?

Solution: Do what's best for the picture. (And hope that nobody notices.)

Note to self: Thumbnails.

Second version: I cut another linoblock, and transferred the image again, this time, the other way round. I started cutting and printing. Printed the first layer; the second layer; the third layer. On about the fourth layer, when I was using darker colours, I saw something was wrong: they weren't printing evenly.

I changed the pressure on the press, increasing it, decreasing it. No difference. With the blanket; without the blanket; rubber sheet instead of the blanket. No difference. Put the print in the other direction; change the ink; change the roller. No difference.

Sometimes the block went through the press too easily; sometimes it wouldn't move. There was only one factor left: the press itself. I had to face up to it: the press had died.

Solution: Buy a new press.

Which took some time: Sorting out the finance; arranging the delivery; fighting with delivery men who think it's OK to leave a 100 lb press in next door's front garden.

But it was worth it.

No excuse now to get on and print.

Third version: I printed my usual near-white backgrounds on about twenty sheets. I cut another linoblock and transferred the image (that's the third time, if you've lost count). I started printing.

Of course, getting used to a new press can take some time...

Oops. Wasted the entire pile of background sheets while trying to get the pressure right. At first I thought it was wrong, because the block went through so easily. Took time to realise that it was because the press is so well-engineered.

Note to self: Never experiment on important bits of paper.

Fourth version: On the positive side, I still had cut only the first layer from the block. I reprinted the backgrounds by using another block the same size, and then, at last, oh it's only been about four months, I was able to start printing again.

Now the press is set up correctly, it's printing beautifully, and effortlessly. Here's the first layer:

Linocut, stage 1

To get some variation in what will be beds of flowers, I inked the block in selected places, using different colours. (Which works well -- apart from when you've finished, you realise that you have five rollers to clean...)

I'll get on with the next layer.